A behind the scenes look at how this image was created and the work that went into building each component. *UPDATED*
This image and the rest of the series can be seen over at the main site:
A few weeks ago I put together this shoot as a portfolio builder and as a potential starting direction for a major unit in my final year at university. The concept started after I saw Simeon Quarrie's work for a couple. He had stated in a BTS that the rain machine they had ordered had not turned up, so they simply built their own instead. So I did the same! I had no idea what i wanted to do with it, but it was a quiet summer!
<br>
Also this post is being entered into the
DIYPhotography Blog's "How I Took It" Contest
*UPDATE*
I won the competition! As can be seen on the announcement post here:
http://www.diyphotography.net/the-winner-of-our-how-i-took-it-contest-is
The rain machine build:
Surprisingly easy job this, just a few bits of wood and a hose pipe.
Started off with 2 long bits of wood (can't remember the measurement but doesn't really matter (also don't use untreated wood like I did if you intend to keep it, it will rot)) crossed them over and drilled a hole through both, fixing together with a nut, bolt and a couple washers, then roughly cut 4 brace pieces to stop it twisting around. They were simply screwed into place.
Now using a hosepipe and a hell of allot of zip/cable ties I simply spiralled out from the centre trying to keep it fairly even distance between them. After trimming the zip ties I started making the holes; Bare in mind that in order for it to look natural as rain, it has to spray upwards and then fall at gravities pace. To start with, based on information gleaned from the internet i used a tiny drill bit and drilled them. This was a terrible idea. instead use a spike, like a pin or one of these:
I don't know what it's for but it was perfect. I did the holes every few cm, but that also turned out to be a mistake, leave a good few inches, there will be a lot of them!
The legs were a bit rubbish, i figured 4 of the same bits of wood would do it, but they didn't I recommend using a hook in the centre and hanging it above the subjects if possible. In the end I used 2 of the legs attached with standard shelf brackets and propped the front of it up over my backdrop stand. (backdrop stand weighed down by paving slabs)
The Shoot:
The shoot was quite a challenge. It was all done on my driveway and as the garage has white doors, we opened them up and put hung black material (the stuff you put under gravel paths to stop the weeds coming through - all I had lying around) held up with clothes pegs onto the drain pipe.
Then the lights had to go around the rain machine without getting wet, we used plastic bags to cover the power supplies, other than that it was down to getting the water pressure just right so that it didn't spray too high or far.
I had a 4 light set-up for the image, one strobe was taped onto the shaft of the reflector umbrella that they are holding in shot.
Once set up (light set-up diagram below) I had a nightmare in which my cheap ass Chinese radio triggers decided to break, I had used all of my available lights already so I had to resort to switching everything to slave mode and triggering them all with the on camera flash. At the distance was shooting from this proved quite temperamental!
Every few shots my 1st assistant would pump smoke into the back of the scene and wait for it to spread out so it wasn't too clumpy.
By the end of the shoot it started raining properly so we had to bail and disassemble it all in an insanely quick time before someone got electrocuted.
The gear:
- Nikon D800
- Nikkor 85mm 1.8D
- 2 x Nikon SB900 speedlights
- Lastolight background stands
- Smoke machine
- 2 x Bowens 500w Gemini Strobes
- 2 x 120 octaboxes (only used one in the end)
- Radio triggers (that failed on me (don't buy cheap shit))
- 5in1 Reflectors
- Rain Machine
- Wacom Intuos 4 (for post production)
- A BANANA!
THAT'S IT!
That's how I did it, I will in future be doing this in video form, I didn't have a whole lot of assistants in this shoot! The post production work was long and laborious. Removing the frame of the light stand and allot of dodging and burning.
Massive thanks to No.1 aka Scott Luck for his assitance and to the models Doug, Issi and Richard.